How to move old threes in construction without cut them?
Moving a tree and planting it after removing it from the ground can be daunting. But with the right instructions, novice gardeners can move most of the smaller trees. Do not worry, in this article we are going to answer the question “How to move old threes in construction without cut them?”
By assessing the condition of the tree and keeping the ball of intact roots, the tree can be kept healthy until it is ready for planting.
Tree Relocation (Part I)
Step 1: Prepare the plant (to move the tree)
Check if the tree is healthy enough to move. If the tree is unhealthy, it is likely to die of shock while moving.
If the tree is dehydrated or diseased, try to treat the disease as much as possible before transplanting.
Trees older than 3 years are likely to be damaged during relocation if you do not follow the handling tips and do not use special materials.
Step 2: Tree Sleep Season (Autumn)
During the tree sleeping season, he performed the tree relocation operation. The best time to plant a tree is mid-autumn to late winter. When the so-called tree is dormant and less likely to be damaged. If the tree is healthy and does not need to be planted immediately, keep it in its original location until the dormant season.
He cut the tree off the ground. Using a shovel, he moved the topsoil around the roots, which is close to the trunk of the tree. These roots form the root ball of the tree. Dig the root under the ball and pull the tree up and out of the ground. Dig 25 to 30 cm of root ball for every 2.5 cm of tree trunk diameter. 24 hours before removing the tree, water the soil to make it easier to dig.
The root ball of the tree should be completely covered with a cloth or sack. Using a small shovel, he removed all the soil masses from the root ball. Suture the sack tightly around the tree with a special needle.
When moving trees, keep the root ball intact. When the tree is moved to its new location, it must be picked up by the trunk. (Root it on top of the ball to prevent it from taking root.) If the tree is too heavy to carry, place it in a van or cart or move it by crane.
Immediately after removing it, replant the tree. If possible, plant the tree the same day and do not keep it on the ground in a twisted sack.
Tree Relocation (Part II)
Step 1: Place and plant the tree in the new location
Make sure the new location fits the tree. If the tree was fresh and vibrant in its old place, you should choose a place with the same type of soil, climatic conditions and shade level. Investigate the condition of the tree. Do not destroy the tree to improve its health.
Dig a hole about the depth of the old tree hole. If the hole is too deep, it will cause root rot when the tree is watered. However, the hole should be drilled about 2-3 inches (5.1-7.6 cm) larger than the main hole to add more mulch and top layer.
Note: Before drilling, make sure that water and gas pipes, power cables and telephones pass through.
The packaging made by the sack should be separated from the root ball. The winding will restrict oxygen to the roots. This, in turn, can create a belt that eventually destroys the tree. To prevent this, the packaging must be completely removed before planting the tree in the new location.
Carefully place the tree inside the hole. To avoid damaging the tree, do not throw it into the hole. Planting is often harmful to trees and should be placed gently in the hole. He lowered it into the hole and adjusted it so that the trunk was straight.
Use a shovel to ensure it is level with the ground. Place the shovel handle on the floor and across the hole. The top of the root ball should be flush with the surface of the hole. If the root ball is too deep in the ground, remove it and return some soil into the hole to level the root surface.
Fill the hole with topsoil. The tree needs a lot of organic matter and nutrients to adapt to its new location. Prepared topsoil, compost or a combination of these.
He circled the special soil around the roots of the tree until it filled the hole upwards. A loamy topsoil with a uniform mixture of sand, silt and clay is ideal for planting trees.
Tree Relocation (Part III)
Step 1: Take care of the displaced tree
Add a layer of mulch 2-3 inches (5.1-7.6 cm) around the base of the tree. Rub the mulch in a loop a few inches (cm) away from the trunk. This helps the tree maintain the moisture and moderate temperature of the soil around the plant. The mulch ring should not be deeper than 3 inches (7.6 cm) to prevent the tree from choking.
Immediately after planting, your tree should be watered. After planting the tree, the soil should be kept moist by watering. Using a constant flow hose, water the tree for 30 seconds at a time. Irrigate once or twice a week (depending on the temperature). Tree soil should be moist. But too much watering will cause the plant to die and the roots to rot. Water your tree two to three times a week during the summer or in hot weather.
If you click on this link, you will redirect to:
Check out the Latest coffee tips on the coffeemag.ca : EVERYTHING YOU NEED TO KNOW ABOUT GROUND COFFEE
Restrained the trees in windy weather. A restraint system should be set up to prevent the tree from falling while it has not yet taken root. He tied the tree trunk to the ground with a few straps.
Of course, in the case of large trees, the implementation of the restraint system must be done by the tree relocation company. Examine the hazards regularly to avoid damage.
He did not prune the tree vigorously for a year. After planting the tree, he pruned it and removed the dry or broken branches. Wait at least a year if large branches are to be removed or the tree reshaped.
Avoid fertilizing the tree for 2 to 3 years. Transplantation is not recommended for newly transplanted trees because it is ineffective until the tree roots are revived.